Skip to content
Krieg Solutions

Design & 3D printing Ontario

Custom parts,
and my own designs.

I’m Kyle Hemphill. I design and print parts for other people, and I design a small line of my own for sale. Both come off the same printer in my Ontario shop.

A sketch, a photo or a CAD file is enough to start.

Upper and lower transmission-mount fitment prototypes on the printer bed
Upper and lower 996 mounts, printed to check fitShop photo
Typical lead time
24 to 72 hours
Design and print
1 to 2 weeks
Build volume
270 x 270 x 256 mm
Typical tolerance
±0.2 to 0.4 mm

Case study / 01

Fit checked in PETG, then machined in aluminium.

A customer needed upper and lower transmission mounts for a Porsche 996 911 that were stronger than the factory parts, with enough flexibility to suit an engine swap. The design was the customer’s, not mine. I advised on printability, split each mount into two sections with dowel joints so each one fitted the 270 x 270 x 256 mm envelope, then printed them in PETG and iterated several times until the fit and tolerances were right. These were fitment prototypes for checking the design, not service parts. The design then went to billet aluminium, machined elsewhere.

Upper and lower transmission-mount fitment prototypes, printed in two sections each
Upper and lower mounts, two printed sections each
Close view of a printed transmission-mount prototype
A closer look at one prototype
Rendered view of the modular wallet and its removable plates
Design render Modular wallet
Shop on Etsy

New shop, nothing listed yet. It fills up as the pegboard line is finished.

My own designs / 02

Some of what I make is for sale.

Most of the work here is for other people. I also keep a small product line of my own: designs I own, print and revise myself, sold through my own shop rather than made to order.

Modular wallet
Finished design. I modelled it in Fusion 360, printed and revised it on the QIDI Q2, and its plates can be replaced or reconfigured without replacing the whole wallet. The animation shows the design; the wallet itself is a finished print.
Pegboard storage, in development
A range of tool holders for IKEA Skadis boards. Some parts are printed and tested. The line goes on sale when there are enough of them to be worth browsing, not before.

Need something that does not exist yet? That is the other half of the job.

Starting a job

Send what you have.

  1. A broken part

    Send photos of the original and where it fits. Include a ruler in one photo or give approximate dimensions.

  2. A sketch or model

    Start with a sketch or attach your CAD file. Say what the part needs to do and where it will be used.

  3. A small batch

    Send your model or dimensions, quantity and target date. If fit matters, include the mating dimensions.

Check materials and fit limits

Before you order

Good questions.

What will my part cost?

Cost depends on the design work, size, material, quantity and any critical fits. Send what you know so I can check whether it is a fit for the shop and quote the actual job.

Do you sell your own parts?

Yes. A modular wallet, and a range of pegboard tool holders for IKEA Skadis boards that is still in development. They sell through my Etsy shop, which is new and has nothing listed yet; it fills up as the pegboard range is finished.

How soon can I get it?

Single printed parts typically leave the shop in 24 to 72 hours. Design work typically takes 1 to 2 weeks from concept to finished part, depending on complexity. There is one machine and one queue. Rush may be possible, but ask before counting on it.

How accurate are the prints?

Typical tolerance is ±0.2 to 0.4 mm, depending on geometry and material. For a critical fit, I design the tolerance in and print test coupons. Critical features can be reamed or machined to spec. Include the mating dimensions in your email.

Do I need a CAD file?

No. Start with a photo of the broken part or a sketch and rough dimensions. If you have a model, attach a STEP, STL, OBJ or 3MF file to your email.

What materials can you print?

PLA, PETG, ABS, ASA, TPU, polycarbonate (PC), carbon-fibre nylon (PA-CF) and glass-fibre nylon (PA-GF). The QIDI Q2’s actively heated chamber makes polycarbonate and the filled nylons viable in this shop.

Can your part be printed?

Email what you have. I’ll check the job before quoting cost and timing.